| Environmental |
| Enclosure |
Type 1 |
| Ambient Temperature |
+14℉ to +104℉ (-10℃ to +40℃) |
| Storage Temperature |
-4℉ to +149℉ (-20℃ to +65℃) |
| Humidity |
5% to 95% with no condensation |
| Altitude |
0 to 3,300 ft. (1,000m) without derating, derate output current by 1% for each
additional 330 ft (100m) |
| Codes and Standards |
| UL, cUL Listed per UL508A |
| Conforms to applicable NEMA ICS, NFPA, & IEC Standards |
| Electrical |
| Input Voltage: Nominal – Phase |
208VAC, 230VAC, 460VAC – 3 Phase |
| Input Voltage: Tolerance, Unbalance |
+/-10%, ≤3% |
| Input Frequency |
60Hz +/-5% |
| Displacement Power Factor |
≥0.97 |
| Output Frequency |
0.00 ~ 400.00Hz |
| Motor Control Method |
V/F for all capacity range |
| PWM Switch Frequency |
1 ~ 15kHz (2~ 40HP)
1 ~ 10kHz (50 ~ 75HP) |
| Drive Overload Capacity |
120% for 1 min – 208V/230V: 2~25HP, 460V: 2~75HP |
| Motor Overload |
Programmable overload / EMPR |
| Torque Boost |
Manual 0~15% boost, automatic torque boost available |
| Speed Reference |
Keypad, 0~10V, -10~10V, 0~20mA, RS485, Fieldbus, Pulse – 208V/230V: 2~25HP, 460V: 2~75HP |
| Speed Reference Resolution |
Digital command: 0.01Hz
Analog command: 0.06Hz (60Hz standard) |
| Acceleration/Deceleration Time |
0.00 ~ 6000.0 seconds |
| Jump Frequencies |
3 programmable jump frequency |
| Output Signals |
Qty 4: N.O. dry contacts rated 5A @ 230V max, functionality: Drive Run, Drive Fault,
Bypass Run, & Damper Control (for Fan)
Qty 1: Open Collector rated 50mA @ 26VDC max, functionality: Drive Run (for Pump)
Qty 1: Form C dry contacts rated 2A @ 230V max, functionality: Drive Fault (for Pump)
Qty 1: 0 to 10VDC or 4 to 20mA, user selectable programmable analog signal (for both
Fan & Pump) |
| Operation Features |
| Soft Fill |
Prevents pump damage caused by dramatic pressure changes during initial operation. |
| Start/End Ramp |
Prevents pump damage by changing the acceleration and deceleration ramp profile
during initial pump operation and stop. |
| Decel Valve Ramp |
Prevents pump or pipe damage caused by sudden pressure changes when pumps
are stopped or valves are closed. |
| Scheduling (Time Event: Real Time Clock) |
Real Time Clock allows sequencing of selected functions during pre-defined time periods. |
| Flow Compensatione |
Compensates for hydraulic losses due to elevation or long pipe lengths. |
| Pump Clean |
Removes foreign substances from the pump cavity to extend life and improve efficiency. |
| Load Tuning |
Estabilishes load curves (current & power) to define load characteristics for under
torque and pump clean funtions. |
| Fire Mode |
Operates continuously to protect critical systems during emergency situations under
set frequency and direction. |
| Energy Savings Display |
Commercial energy consumption is compared to the energy utilized by the VFD to
calculate the amount energy savings. |
| Certificate/Compliance |
UL, CE |
| Power-On Resume |
Automatic restart upon power interruption. |
| Sleep, Sleep Boost, Wake-up |
Standby mode during PID operation for energy savings and reduction of pump wear. |
| Auto Torque Boost |
Manual or automatic voltage compensation for varying load profiles |
| Lubrication Control |
Lubrication output signal for a defined time period prior to drive control starting. |
| Damper Control |
Damper control with end-switch confirmation with programmable time period. |
| Level Detection |
User defined low and high detection limits based upon voltage, current or feedback. |
| Pipe Break Detection |
Upon PID operation, pipe breakage or leakage is detected to display a warning or fault condition. |
| Underload Detection |
No flow or pump dry detection with selectable response. |
| Motor Pre-heat |
Prevents condensation in the motor by injecting direct current during idle states. |
| Kinetic Energy Buffering |
Upon loss or momentary power interruption, the drive maintains DC bus voltage
by controlled regeneration of the load. |
| Macro Setting |
Application specific parameter groups for commonly used functions. |
| Bypass Features |
Manual bypass selection. |
| Automatic transfer to bypass |
| Bypass run indication |
| Motor overload indication. |
| Power on indication. |
| Hand/Off/Auto selector switch. |
| VFD/Off/Bypass selector switch. |
| Adjustable trip class for bypass contactor. |
| Damper end switch logic with notification. |
| Drive and bypass input/output contactors. |
| Drive input isolation contactor |
| Control power transformer with fusing. |
| Five built-in relay outputs. |
| Built-in DC reactor. / Built-in 3% AC Line reactor as an option. |
① Rated Motor
